Dry-supplied pouch format
Pouches are stored and shipped before water activation, then prepared at the packing site.
1 / 1 Ice Pack · Water-Fill / Water-Activated Ice Packs
Water-Fill Ice Pack Range
Dry-supplied coolant pouches activated with water at the packing site. Reference sizes range from nominal 100 to 600 ml; select the pouch, fill target and conditioning procedure for your packout. A packout is the complete arrangement of the product load (payload), coolant and insulation inside the shipper. Conditioning means pre-freezing or bringing the coolant to its required starting state. An ambient-temperature profile describes route and seasonal temperature exposure on the shipping lane.
Reference nominal sizes100 ml / 9 × 12.5 cm; 200 ml / 10 × 15.5 cm; 400 ml / 12 × 19.5 cm; 500 ml / 12.5 × 21 cm; 600 ml / 13 × 23 cm
Pouch materialPE
Internal coolant systemGranular water-absorbing coolant; confirm formulation and dry fill for the selected model
Nominal phase-change material transition option0 °C
Shipping configuration note:The product is a coolant component. Quantity, conditioning and placement must be established with the payload, insulation, ambient profile and route duration.
Product Overview
Water-Fill Coolant Pouches for On-Site Activation
These dry-supplied coolant pouches are filled with water, allowed to hydrate and then frozen at the packing site. Select the nominal size, pouch construction, fill target and conditioning procedure to match the insulated shipper and payload.
Controlled fill target
A model-specific fill line, mass or volume supports repeatable hydrated weight and freezer preparation.
Compact single-pouch placement
Select nominal size and dimensions to fit the available coolant space inside the insulated shipper.
Production-ready specification
Confirm film construction, dry fill, closure, water target, tolerances and carton packing before production.
Typical applications
- Chilled food and seafood packouts after fit, material and thermal validation.
- Insulated bags and cartons where a compact single pouch is preferred.
- Medicine or sample transport only within a qualified shipper and controlled procedure.
- Programs that can manage water filling, closure inspection and freezer conditioning at the packing site.
Information needed for selection
- Required product temperature range and transit duration
- Product load (payload) mass, dimensions and starting temperature
- Insulation, internal space, shipping lane and seasonal exposure
Product role:This water-fill pouch is activated and conditioned before use as one coolant component in a passive cold-chain packout—the complete arrangement of payload, coolant and insulation inside the shipper. Conditioning means filling, hydrating and freezing the pouch to its specified starting state before loading.
Product Specifications
Configuration and Order Specifications
Use these reference options to select a starting configuration. Final values are recorded in the product drawing and order specification before sampling or production.
Product typeWater-Activated Injection Ice Pack
Order basisFinal values confirmed in the product specification
| Specification | Reference data | What to confirm |
|---|---|---|
| Reference nominal variants | 100 ml / 9 × 12.5 cm; 200 ml / 10 × 15.5 cm; 400 ml / 12 × 19.5 cm; 500 ml / 12.5 × 21 cm; 600 ml / 13 × 23 cm | Confirm for selected configuration. Capacity definitions and tolerances are not supplied. |
| Reference outer material | PE | Confirm resin/film structure, thickness and closure. |
| Internal coolant system | Granular water-absorbing phase-change material | Confirm formulation identity and dry fill mass for the selected model. |
| Reference nominal phase transition | 0 °C | Confirm for selected configuration. Not a guaranteed payload temperature. |
| Activation | Fill with water to controlled target, hydrate, inspect and freeze | Each size requires a model-specific instruction to be established and approved before use. |
| Thermal duration | Confirm with technical sales | Confirm with technical sales. Qualify the selected variant in the complete packout. |
Before ordering:For an accurate quotation, confirm: 100–600 ml variant definitions; reference dimensions; PE construction; dry fill by size; water fill target; 0 °C nominal transition; food/medicine suitability; reuse life. These items will be recorded in the final product specification.
Use & Packout
Fill, Seal, Condition and Load to Procedure
Control the water target, seal integrity, freezer preparation and loading position for the selected pouch.
Confirm the pouch
Verify the model code, nominal size, pouch construction, water target and closure method against the selected instruction.
Fill to the specified target
Add clean water to the stated fill line, mass or volume and allow the internal absorbent material to hydrate completely.
Seal and inspect
Secure the opening as instructed, wipe the pouch dry and check the closure and seams for leakage.
Freeze and condition
Freeze in the specified orientation until the complete pouch reaches the required starting state.
Load the documented packout
Use the specified pouch quantity and positions in the validated shipping arrangement and remove damaged pouches from service.
Complete shipping system performance
Thermal performance and hold time depend on the complete packout.
Confirm the minimum and maximum product load, coolant quantity and pre-freezing or conditioning method, insulated shipper, ambient-temperature profile for the shipping lane and transit duration in a defined complete-packout thermal test or qualification protocol.
WHO pharmaceutical cold-chain shipping-container guidance
ISTA 7E thermal transport testing overview for parcel delivery
FDA sanitary-transportation responsibilities for applicable food operations
These references explain industry qualification and transport practices. They do not certify this product or replace testing of your complete packout. Using an ISTA 7E profile alone does not constitute ISTA certification.
Project Configuration
Configure the Product Around the Packout Requirement
Share payload, usable internal space, temperature requirement, transit duration, route profile, order volume and presentation needs for technical and manufacturing review.
Nominal fill target and pouch dimensions after drawing/seal review.Film and injection-opening/closure construction after compatibility tests.Printed fill line, instructions, branding and lot traceability.New sizes and packout studies subject to minimum order quantity, tooling, lead time and requalification.
Product Documents
Request Documents for Your Selected Configuration
Available documents vary by model, material construction and coolant formulation. Ask us to confirm the files available for your quotation or sample.
Technical Data Sheet (TDS)
Dimensions, weight or capacity, material construction, conditioning instructions and carton-packing data for the selected model.
Safety Data Sheet (SDS)
Handling and disposal information for the selected coolant formulation, where applicable.
Product Drawing & Carton Data
Product dimensions, artwork area and carton data for the selected model.
Frequently Asked Questions
Before You Select This Product
Use these answers for initial selection. For ordering and packout setup, follow the specifications and instructions confirmed for your model.
Reference nominal sizes are 100, 200, 400, 500 and 600 ml. Final capacity basis, dimensions and tolerances are confirmed on the product drawing.
Only when the selected pack is used inside a qualified complete system with material documentation, a defined payload range, an ambient profile and controlled operating instructions.
No. A reference coolant transition point does not guarantee payload temperature. Coolant placement, insulation, load and ambient exposure determine the system response.
Submit the required envelope, water-fill target, packout constraints and volume for capability review. A new size needs a drawing, seal validation, conditioning instruction and usually thermal testing of the complete packout.
Quote & Sample Request
Tell Us About Your Packout
Share the information below so our team can recommend a suitable product configuration.
- Product load (payload) weight, dimensions and starting temperature
- Required product temperature range or holding objective and route duration
- Insulated package type and internal space
- Ambient-temperature profile for the shipping lane
- Order quantity, printing and sample requirements
Selected product
Water-Fill Ice Pack Range
We will review a standard or custom configuration after receiving your project details.
Our response will cover the selected model, available documents and sample options.