Flexible segmented coverage
Cell grids support sidewall, top or wraparound placement where the selected construction and seam geometry permit.
1 / 4 Ice Pack · Hydrate Dry Ice Packs
Dual-Surface Hydrate Dry Ice Pack for Seafood
A dual-surface Hydrate Dry Ice Pack for seafood shipping packouts in wet handling environments. Its segmented water-activated cooling-sheet structure supports water absorption from either face, subject to confirmation on the selected drawing. Confirm facing materials, cell layout, hydrated mass, puncture controls and freezer conditioning before loading.
Absorption configurationDual-surface option — confirm on product drawing
Cell count and sizeConfirm on product drawing
Pouch material optionsPE/PA, PE/PET, laminated non-woven or kraft paper
Nominal phase-change material transition option0 °C
Shipping configuration note:The product is a coolant component. Quantity, conditioning and placement must be established with the payload, insulation, ambient profile and route duration.
Product Overview
Hydrate Dry Ice Pack for Seafood Wet Packouts
This Hydrate Dry Ice Pack uses a segmented water-activated sheet structure that is hydrated and frozen before use in seafood packouts. Confirm the dual-surface facing construction, cell layout, hydrated mass, puncture controls and conditioning procedure for the selected design.
Dry supply for local activation
The sheet is hydrated at the packing site to the model-specific target mass before freezer preparation.
Repeatable coolant preparation
A controlled hydration, drainage and freezing procedure helps keep coolant mass and starting state consistent.
Packout-fit selection
Confirm cell count, sheet size and hydrated mass against the available space and coolant placement in the insulated shipper.
Typical applications
- Seafood and fish distribution packouts designed for a wet or high-moisture environment.
- Insulated-carton trials requiring a coolant sheet that can conform around trays or liners.
- Chilled-food packouts after confirming material suitability and payload-temperature criteria.
- Packing operations seeking dry inbound coolant and on-site water activation.
Information needed for selection
- Required product temperature range and transit duration
- Product load (payload) mass, dimensions and starting temperature
- Insulation, internal space, shipping lane and seasonal exposure
Product role:Hydrate Dry Ice Pack is the commercial product-category name for this water-activated cooling sheet; it does not contain solid carbon dioxide (dry ice). It is one coolant component in a passive seafood packout—the complete arrangement of seafood load, coolant and insulation inside the shipper. Hydrate, drain and freeze it to the specified starting state before loading.
Product Specifications
Hydrate Dry Ice Pack Specifications
Use these reference options to select a starting configuration. Final values are recorded in the product drawing and order specification before sampling or production.
Product typeHydrate Dry Ice Pack / Water-Activated Cooling Sheet
Order basisFinal values confirmed in the product specification
| Specification | Reference data | What to confirm |
|---|---|---|
| Activation-facing concept | Dual-surface water absorption | Confirm for selected configuration. Request a cross-section drawing and activation test. |
| Cell count and size | Confirm for selected configuration | Confirm cell count, dimensions and model mapping on the approved drawing before selection. |
| Reference family materials | PE/PA, PE/PET, laminated non-woven or kraft paper | Confirm the two facings and exact layer stack. |
| Reference family phase transition | 0 °C | Confirm formulation and tolerance for the selected configuration. |
| Conditioning | Hydrate, drain, inspect and freeze | A product-specific activation work instruction is required. |
| Thermal duration | Confirm with technical sales | Qualify the complete seafood packout. |
Before ordering:For an accurate quotation, confirm: dual-surface absorption construction; specific cell count; specific dimensions; exact outer layers; 0 °C nominal transition; hydrated mass; food-contact status. These items will be recorded in the final product specification.
Use & Packout
Hydrate, Drain, Condition and Load to Procedure
Control hydrated mass, drainage, freezing and handling for the selected sheet before loading it into a validated shipping arrangement.
Confirm the sheet
Match the model code, cell count, dimensions and facing construction to the selected product drawing and activation instruction.
Hydrate to the target mass
Use clean water and stop activation at the model-specific hydrated mass or other stated acceptance criterion.
Drain and inspect
Remove excess surface water, check all cells and seams, and reject any sheet with punctures, delamination or leakage.
Freeze and condition
Freeze with adequate airflow until the complete sheet reaches the required starting state in the selected work instruction.
Load without puncture
Place the specified sheet quantity and orientation in the documented packout, protecting it from sharp edges and excessive compression.
Complete shipping system performance
Thermal performance and hold time depend on the complete packout.
Confirm the minimum and maximum product load, coolant quantity and pre-freezing or conditioning method, insulated shipper, ambient-temperature profile for the shipping lane and transit duration in a defined complete-packout thermal test or qualification protocol.
WHO pharmaceutical cold-chain shipping-container guidance
ISTA 7E thermal transport testing overview for parcel delivery
FDA sanitary-transportation responsibilities for applicable food operations
These references explain industry qualification and transport practices. They do not certify this product or replace testing of your complete packout. Using an ISTA 7E profile alone does not constitute ISTA certification.
Project Configuration
Configure the Product Around the Packout Requirement
Share payload, usable internal space, temperature requirement, transit duration, route profile, order volume and presentation needs for technical and manufacturing review.
Facing and outer-layer selection after wet-environment compatibility review.Cell grid, sheet dimensions and edge-seal design.Printed activation/handling instructions and branding.Seafood-packout samples and qualification support subject to minimum order quantity, lead time and change control.
Product Documents
Request Documents for Your Selected Configuration
Available documents vary by model, material construction and coolant formulation. Ask us to confirm the files available for your quotation or sample.
Technical Data Sheet (TDS)
Dimensions, weight or capacity, material construction, conditioning instructions and carton-packing data for the selected model.
Safety Data Sheet (SDS)
Handling and disposal information for the selected coolant formulation, where applicable.
Product Drawing & Carton Data
Product dimensions, artwork area and carton data for the selected model.
Frequently Asked Questions
Before You Select This Product
Use these answers for initial selection. For ordering and packout setup, follow the specifications and instructions confirmed for your model.
For the dual-surface option, confirm whether both faces are water-permeable and the target hydrated mass in the activation specification. Hydrate, drain and freeze the selected pack before loading.
Direct food contact is not assumed. If contact is required, specify it and request material declarations and compliance documents for the selected construction.
No universal duration can be assigned from the sheet alone. Test the exact insulated container, seafood load, coolant quantity, starting temperatures and route profile.
Keep the sheet away from sharp shells, bones and tray edges, inspect before every use and reject any punctured, leaking, delaminated or open-seam unit.
Quote & Sample Request
Tell Us About Your Packout
Share the information below so our team can recommend a suitable product configuration.
- Product load (payload) weight, dimensions and starting temperature
- Required product temperature range or holding objective and route duration
- Insulated package type and internal space
- Ambient-temperature profile for the shipping lane
- Order quantity, printing and sample requirements
Selected product
Dual-Surface Hydrate Dry Ice Pack for Seafood
We will review a standard or custom configuration after receiving your project details.
Our response will cover the selected model, available documents and sample options.