Insulated Shippers & Containers · Insulated Cooler Box

100 L VPU-Series Soft-Sided Insulated Cooler Box

A soft-sided protective carrier shown with a rigid inner box and reflective insulation component for passive shipping projects. The 100 L designation is a nominal reference whose gross and usable-volume basis must be confirmed, together with the complete component list and packout configuration.

Soft protective outer carrierRigid internal enclosureReflective insulation componentsNominal capacity to confirm
Product formatSoft-sided carrier with rigid insert
Model-family designationVPU; confirm VIP, PU or composite construction
Capacity reference100 L nominal; confirm from current drawing
Temperature performanceComplete-system qualification required
Shipping configuration note:The soft outer carrier, rigid inner box, reflective insulation component, coolant and payload must be defined as one assembly. The 100 L description is a nominal reference only until its capacity basis and usable loading space are confirmed on the selected drawing.
Product documents

Product Overview

A Component-Based Carrier Whose Usable Space Must Be Confirmed

The soft transport carrier surrounds a rigid inner enclosure and reflective insulation components. This layered format can protect the insulated assembly during handling, but the meaning of the VPU designation, actual insulation construction, foldability, included parts and usable payload space must be confirmed for the selected model.

01

Protective outer carrier

The soft outer layer provides handles and a secondary enclosure around the internal shipping components.

02

Layered internal assembly

A rigid inner box and reflective component can be specified together around the payload and coolant layout.

03

Large-format planning

The nominal capacity provides a starting point, while actual selection is based on verified internal dimensions and effective payload space.

04

Project-specific control

Closures, internal protection, coolant, monitoring and handling requirements can be listed in one approved configuration.

Typical applications

  • Large temperature-sensitive payloads in qualified passive packouts
  • Pharmaceutical and diagnostic distribution projects with defined route controls
  • Protected laboratory kits and secondary cartons
  • Healthcare or vaccine projects only after the exact complete system is qualified for the intended use

Information needed for selection

  • Product load (payload) dimensions, mass and starting condition
  • Required product temperature range or holding objective and route duration
  • Usable internal space or pallet footprint and load height, closure cycle and route exposure
Product role:A soft-sided protective carrier shown with a rigid insulated insert and reflective internal component. It provides the enclosure for a passive packout; conditioned coolant and a qualified loading configuration determine the shipment temperature profile.

Product Parameters

Product Parameters

Model/Capacity100 L.
Material & StructureSoft-sided outer shell with a rigid inner liner, insulated with VPU (VIP + PU composite) passive material. VIP sandwich: PU (≥ 5 mm) + VIP (≥ 10 mm) + PU (≥ 5 mm); VIP core in glass fibre or fumed silica, thermal conductivity 0.002–0.0045 W/mK. Passive, non-electric operation.
Insulation ThicknessTotal multi-layer build 15–50 mm.
Applicable Temperature RangeChilled operation at 2–8 °C.
Compatible Coolant OptionsIce packs, gel packs or PCM panels; the coolant configuration determines the hold time achieved.

Product Specifications

Confirm Nominal Capacity, Usable Space and the Full Assembly

100 L is the supplier's nominal model description. Request the controlled drawing to confirm its capacity basis, usable payload space after insulation and coolant, complete component list and actual insulation construction.

Nominal capacity reference100 L; definition and usable volume to confirm
Selection basisVerified dimensions, included components and payload fit
SpecificationAvailable basisWhat to confirm
Product formatSoft-sided outer carrier with rigid inner assemblySelected model, closures and component orientation
Nominal capacity100 L referenceWhether this is gross volume, effective payload volume or a model name
DimensionsTo be confirmedExternal, internal and unobstructed usable loading envelope
Insulation constructionVPU model-family designationWhether the model uses VIP, PU or a composite assembly; confirm core, facing, thickness and layout
Outer and inner materialsModel-specificCarrier fabric, coating, rigid insert, facing and cleaning limits
Foldability and serviceTo be confirmedWhich parts fold, detach or can be replaced
Coolant and internal partsProject-specificType, quantity, conditioning, placement and included accessories
Temperature performanceComplete-packout test requiredComplete-packout test with the selected payload and route profile
Before ordering:VPU is the designation used for this model family, but it does not by itself define the insulation. Request the BOM and section drawing to confirm whether the selected construction uses vacuum insulation panels, polyurethane foam or a composite assembly. Match the 100 L designation to the controlled drawing before calculating usable payload space.

Use & Packout

Confirm the Capacity and Included Components Before Packout Design

Start with the actual payload and coolant space rather than the nominal capacity. Confirm which outer, inner and reflective components are included, then establish one assembly and loading procedure for testing.

01

Confirm the capacity basis

Identify whether the nominal value refers to gross internal volume, effective payload space or a model designation and approve the current dimensions.

02

Verify the supplied assembly

List the soft carrier, rigid inner box, lid, reflective insulation components, retainers and accessories included in the quotation and final BOM.

03

Build the loading pattern

Condition the specified coolant, protect the payload from direct contact where needed and keep every component in the defined orientation.

04

Close, monitor and qualify

Secure the inner and outer closures, place calibrated sensors at defined risk points and test the complete system against the intended route.

Complete transport configuration

Thermal performance depends on the complete load and route conditions.

Confirm the minimum and maximum product load, any coolant or other thermal-control component used, starting conditions, closure and opening frequency, route ambient-temperature profile and transit duration in a defined complete-configuration test or qualification protocol.

WHO pharmaceutical cold-chain shipping-container guidance ISTA 7E thermal transport testing overview for parcel delivery FDA sanitary-transportation responsibilities for applicable food operations

These references explain industry qualification and transport practices. They do not certify this product or replace testing of your complete packout. Using an ISTA 7E profile alone does not constitute ISTA certification.

Capacity & Dimension Configuration

The 100 L format can be adjusted in internal liner volume and external dimensions to fit vehicle bays, pallets or manual handling limits.

Shell Fabric, Colour & Logo

Outer shell material colour, printed branding and label panels can be aligned to customer identity across a fleet.

VIP & PU Layer Build

VIP panel thickness and PU layer thickness within the 15–50 mm build, together with the VIP core material, are selected to balance wall slimness against hold time.

Internal Liner Layout

Removable dividers, trays and shelving can be fitted inside the rigid liner to organise mixed payloads.

Coolant Configuration

The quantity and placement of ice packs, gel packs or PCM panels is set per configuration to reach the target 2–8 °C hold time.

Temperature Band & Transport Duration

Configurations are available that support 72, 96 or 120 hours in the 2–8 °C band, with the coolant load and layer build chosen to match the journey length.

Outer Print & Packing

Carton printing and the bulk packing format for fleet or distributor supply are specified to the customer's requirements.

Project Configuration

Define the Capacity, Component List and Route

Share the payload dimensions and mass, required usable space, temperature condition, route duration, ambient profiles, coolant plan, closure, carrying method, cleaning requirements, documentation and order quantity.

Nominal and usable capacityOuter carrier and rigid insertVPU designation and insulation constructionCoolant and payload layoutClosures, handles and labelsQualification documents and packing
Review Documents

Product Documents

Request Documents for Your Selected Configuration

Available documents vary by model, material construction and project requirements. Ask us to confirm the files available for your quotation or sample.

TDS

Technical Data Sheet (TDS)

Dimensions, capacity where applicable, layer construction, closure details and carton-packing data for the selected model.

MAT

Material & Construction Information

Available layer, liner, insulation, closure and applicable material-compliance information for the selected configuration.

DWG

Product Drawing & Carton Data

Product dimensions, artwork area and carton data for the selected model.

Frequently Asked Questions

Before You Select This Product

Use these answers for initial selection. For ordering and packout setup, follow the specifications and instructions confirmed for your model.

Treat 100 L as a nominal model reference. Request the current drawing to confirm the capacity definition, internal dimensions and effective space remaining after the insert, coolant and payload protection are installed.

Quote & Sample Request

Tell Us About Your Transport Configuration

Share the information below so our team can recommend a suitable product configuration.

  • Product load (payload) weight, dimensions and starting temperature
  • Required product temperature range or holding objective and route duration
  • Usable internal space or pallet footprint, load height and closure requirements
  • Ambient-temperature profile for the shipping lane
  • Order quantity, printing and sample requirements

Selected product

100 L VPU-Series Soft-Sided Insulated Cooler Box

We will review a standard or custom configuration after receiving your project details.

Our response will cover the selected model, available documents and sample options.
Scroll to Top